The 10 Scariest Things About Repair Car Keys

How to Repair Car Keys

Car keys may appear small and insignificant, but they are vital to the functioning of your vehicle. Replacing an old key or a modern transponder key can cost up to $200.

There are ways to fix your car keys yourself for a fraction of the price. This article will go over the most frequently encountered car keys problems and the DIY solutions.

Dead Key Fob Battery

Cars come with remote key fobs that allows opening the doors and trunk easier than ever. The battery in this device is susceptible to dying. There are some tricks you can use to solve this problem quickly.

Examine if your car remote key fob repair is still in the ignition mode. If so the battery of the key fob could be low rather than dead. To test this, press the button on the fob against the ignition button on the vehicle. If it works, then the battery is probably working fine and only requires to be replaced.

To replace the battery within the fob, pry open the case using a screwdriver. Do not apply too much force since this could cause the fob's casing to split. If the fob doesn't open, try using your pry tool several times around the outside of case.

Once the fob is open then remove the mechanical key and then open the electronic part of the car. Then insert the replacement battery and then snap the shell together. If the key fob won't work after this, there could be a larger problem with your car's remote control car key repairs start system that requires a professional to diagnose. A reputable mechanic will be capable of helping you if this is the situation. If you require assistance with your vehicle or vehicle, you can get roadside assistance.

Broken Key Ring

There are a few steps you can do when your key fob does not work because the ring has been broken. The first step is to see if the broken piece is still in the ignition. If it's still in there, remove it without damaging the ignition lock or the door lock. If you're having difficulty taking it off, call a locksmith for assistance. They have tools that allow you to safely remove the damaged key from the ignition.

A damaged car key could also be the result of corrosion on the plastic frame or circuit board. Clean the circuit board using cotton swab. This will eliminate the corrosion and prevent damage to the contact pads.

repair car key a damaged ring by using a thick wire or nail to seal the hole. Superglue can be used to fix the broken key ring. After cleaning the ring with a wet cloth apply a small amount of superglue on each end of the nail or wire. Let the pieces dry and then press them into place. These DIY solutions can seem appealing, but they're only temporary solutions. For long-term repairs, it's best to work with an experienced locksmith. They have the expertise and tools to repair car remote control key damaged keys quickly and effectively. They can even replace the battery in your key fob and change it's programming if required.

Broken Key Blade

Some key blades can break from a lot of wear and tear. If this happens, it's time to get a new key. The issue isn't as serious as you might believe at first. The main problem is that the metal blade has snapped away from the case.

One method to fix this is spraying the key hole with a lubricant. Then, you can use pliers tweezers, or a pin to grab the damaged key and pull it out. If the key is magnetic, you can also try using a magnetic tool to help pull it out. Use a magnet to help you remove the key, but be careful to not damage the lock tumbler.

Call a locksmith immediately in the event that you are unable to remove the broken part of the key. They have tools that let them safely remove keys without causing further damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of glue to the edges of the break and press them together. Make sure the glue has dried before inserting the key into the lock. However, this method isn't secure and you may need to repeat the process multiple times before it's successful. Super glue might not be able to hold the key in place. Therefore, this is more of a temporary measure rather than a permanent solution.

Broken Plastic Loop

If the plastic loop is damaged, it can make the key useless. It's a fairly simple fix. You can use wire or a nail for finishing to replace it. Drill two holes in the plastic loop that is broken for each end of the nail or wire. Cut the wire or nail to the desired width and then put a drop of superglue in each hole. Then, press the wire or nail into the holes and allow them to dry.

A locksmith who sells replacement shells is an alternative option. They can take the programmable portion of your key, then transfer it to the new shell and cut the new blade for less than the full replacement cost.

This isn't the best solution, but it will allow you to travel again if your key has been cut in half. However, it can be difficult to repair the blade of the key if it's in the ignition. You can try using a hair clip or needle extractor tool to remove the damaged part of the ignition, but it's risky if not careful. The best solution is to contact a locksmith who has special tools for safely removing damaged keys from the ignition. You can also get a new key made with the correct cuts for the ignition of your vehicle.

Broken Master Key

If a key gets damaged inside the lock, you'll need to try to retrieve it before it gets completely destroyed. You can employ tweezers, lubricants, and needle nose pliers to grasp the broken fragment of a key.

To begin, spray the inside of your lock with a lubricant, such as graphite powder or WD-40. You can also employ the hacksaw blade technique that involves moving the blade along the sides of a broken key and grabbing onto some of its teeth. If you're successful you will be in a position to remove the broken key.

Many hardware stores offer tools for key extraction that spiral. It is a thin, flexible bar with spiral threads, which can be inserted into the keyway and then bent to get into the damaged section of the key. Once it has gotten caught on the serrations, you can turn the bar around and then pull it against the broken part of the key.

Before calling a locksmith, attempt to take out the damaged master key before calling a locksmith. If you're not able to remove the broken piece it's time to call in the professionals. A locksmith can make you an entirely new key that will be programmed using the transponder in your car.