The 10 Most Terrifying Things About Car Key Button Repair

Car key button repair (stuart-Cunningham-5.technetbloggers.De)

A broken car key can be a hassle. You may need to contact an emergency car key repair locksmith service or purchase an alternative remote.

You could be able to save money by repairing your old key fob instead of replacing it. This is especially true when the problem is due to the worn-out switch or defective contact.

Battery

If your key fob's buttons do not respond when you pressing them, it could be a sign that the battery is dead or is about to reach the end of life. Fortunately replacing the battery is an easy task that you can complete on your own instead of hiring a locksmith or dealer to take care of it.

First find the battery compartment. This is usually found on the backside of the key fob and might be hidden behind a slide-out cover or an access point that opens when you push a button. When the compartment is opened, look for the small button-cell battery. It's usually the shape of a small coin and has a plus and the minus symbol. Take the old battery out, and replace it with a brand new one. Make sure that the plus and symbol are aligned correctly.

Once the battery is installed close the compartment and snap the two halves of the key fob. Before closing the door, align and snap the pieces in the correct position. Press any of the buttons to ensure that they work properly.

If your remote keyfob still does not work after replacing the battery, there could be other problems that require a different type of repair. Dropping the device into a pool of water can cause it to stop working. It could also be due to a problem with the internal electrical system or the need to be deprogrammed. Check out these other common automotive troubleshooting methods to determine whether your key fob is suffering from a different issue.

Switches

There are various types of switches that are used in the car key fob depending on the year and model. The older type of key repair service usually has a separate chip which you can see in the case, whereas modern keys are more sophisticated and function by sending signals to the car. Whatever the model of key, the buttons on the key can become worn out or damaged during normal use. As a result, they become difficult to press, or even ineffective. If you try to force the button to function, it can cause further damage and may even stop the key from starting your vehicle in the future.

If you are unable to get your key to function, try changing the batteries. If that doesn't help it may be necessary to clean your key fob and re-adjust the switches. These tiny electronic switches are more likely than larger components of the key to break since they are constantly tossed about.

The switches are rubber-like, and are coated with an electric conductor film that can wear down over time. Fortunately, they are also small and easy to replace. The old ones are soldered to the circuit board, and you'll need to be careful to remove them without damaging anything else. Then you can put in the new ones and reassemble your key fob.

Don't use your car key fob for more than two hours at a stretch and don't leave it out in the open. Also, try to locate a safe place to store your keys when you're not making use of it.

If you've already tried cleaning your key fob and replacing the battery, and the issue persists it's probably time to think about hiring an appointment with a locksmith. A professional locksmith can test the frequency of your key to determine whether your car is able to communicate. They can also open and replace microswitches, alter cases, and much more.

Outer Case

A key fob spends a lot of time jostled around, and when the buttons aren't able to move upwards and downwards within the case, they may become stuck or break. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it could be necessary to take off the case. If the contact points where the buttons touch aren't fitting well or are worn out, adjusting them might be the only solution to correct the issue.

Some keys use rubber buttons which can wear away over time. The rubber stretches and nails cut into it, and the buttons become difficult to press. In this situation the key may fail and it's time to replace the case or button. This repair involves taking apart your remote, finding the button switches on the board, then heating the solder and carefully removing them. New buttons are then soldered to the circuit board. The case can then be rebuilt with the horse shoe key blade piece attached. The new buttons must be securely fitted inside the case to stop them from falling out.

Inner Case

Since your key fob is prone to be tossed around and could occasionally be pressed by accident and the buttons inside may get damaged or stuck over time. If your key fob isn't working when you are away from home, you can solve the issue quickly using metallic tape and punch holes. This will allow you to open doors, but not start the emergency car key repair. This quick fix could allow you to return safely to your vehicle to finish your journey.