The 10 Most Scariest Things About Car Key Button Repair

Car Key Button Repair

A broken car key can be a source of frustration. You might need to contact an emergency locksmith service or purchase an alternative remote.

However, you might be in a position to save money by repairing a worn-out key fob instead of replacing it. This is especially true when the issue is caused by the worn-out switch or defective contact.

Battery

If your key fob's buttons are not responding to your pressing them, this could be a sign the battery has failed or is close to the end of life. Fortunately replacing the battery is a simple task that you can complete on your own instead of paying a locksmith or dealership to take care of it.

First look for the battery compartment. The battery compartment is typically located on the back of the key fob, and is often concealed behind a cover that slides out or a button that opens the access point. Once the compartment is exposed, locate the small button battery. It's usually the shape of the shape of a coin and is identified with a plus and minus symbol. Remove the battery that is old and replace it with a new one. Make sure that the plus and the minus symbols are properly aligned.

Once the battery is in place Close the compartment and snap the two halves of the key fob together. Make sure to align the pieces and secure them properly before closing the door and testing your keys. To ensure that the buttons function correctly, press any of them.

If your remote keyfob still does not work after replacing the battery, there may be other issues that require a different form of repair. The fob's dropping into a pool of water can cause it to cease functioning. Or, it could be suffering from an electrical issue within the device or might need to be deprogrammed by a dealer or locksmith. Find out if the problem is with your key fob by using these other common automotive troubleshooting methods.

Switches

Depending on the year and make, there are different kinds of switches available that are used in the keyfob of your car. The older model keys usually have an additional chip that is visible inside the case, whereas the modern keys are more sophisticated and function by sending signals to the car key repair shop near me. No matter what type, the keys' buttons can get worn down or damaged when used regularly. As a result, they become difficult to press, or even ineffective. If you try to press the button too hard it could cause further damage and potentially stop the key fob repairs near me from starting your vehicle in the future.

If you can't get your key to function, try changing the batteries. If that doesn't help it may be necessary to clean your key fob and re-adjust the switches. These tiny electronic switches are more susceptible than larger parts of the key to break due to the fact that they are constantly jostled.

The switches feel rubbery and are coated with a film that conducts electricity. The film is prone to be worn away over time. Fortunately, they're small and affordable to replace. The old ones are soldered onto the circuit board, and you'll have to take care to remove them without damaging anything else. You can then solder the new ones in and reassemble your fob.

Do not use your car key fob for more than a couple of hours at a time, and do not leave it open. When you're not using your key, keep it in a secure location.

If the problem persists after you've cleaned the key fob, replaced the battery and tried to clean it, then you may need to talk to an expert locksmith. A professional locksmith can test the frequency of your key to determine if it's still able to communicate with your vehicle, open and replace micro switches, swap cases and more.

Outer Case

Key fobs spend a lot of time jostled around and when the buttons aren't allowed to move upwards and downwards within the case, they may become stuck or broken. If cleaning the case using rubbing alcohol and a cotton swab fails to work, it could be necessary to take off the case. If the contacts where the buttons touch aren't fitting well or are worn out, adjusting them could be the only solution to correct the issue.

Rubber buttons can get worn out over time. The rubber expands, nails gouge into it and the buttons can become difficult to press. In this case the key may fail and it's time replace the case or the buttons. This repair involves taking apart your remote key fob repair, locating the buttons on the board, then heating the solder and carefully removing them. New buttons are then soldered to the circuit board. The case can be reassembled and the horseshoe key blade can be attached. The new buttons should be securely fitted into the case in order to stop them from falling out.

Inner Case

Since your key fob is likely to be tossed around and could occasionally be pressed by accident, the buttons inside can be damaged or stuck over time. Utilizing metallic tape and a hole punch you can fix this problem in the event that your vehicle is away from home when the key fob doesn't work and allows you to open the doors, but not to start the engine. This simple fix will allow you to safely get back to your vehicle and complete your journey.